Monash Biotech Pvt. Ltd.
HomeAbout UsQuality PledgeResourcesSupport

FAQs on Micropipette Handling, Alignment & Setup FAQs

Micropipette Handling, Alignment & Setup FAQs

Micropipette Handling, Alignment & Setup FAQs

Are hydrophilic-coated pipettes better for embryo manipulation ?


Advantages: Reduce cell adhesion and sticking to glass Improve fluid flow, minimizing drag inside the lumen Considerations: Coating wear over multiple uses—monitor performance Slightly increased cost per pipette


Yes, our Injection Micropipettes offer a range of angles from 15° to 35°, as well as 0° (straight). This versatility allows you to choose the optimal angle for your specific ICSI procedures.


Bevel Angle (10–15°): Provides a sharp “knife-edge” for clean membrane penetration Symmetry: Even bevels reduce lateral forces that can tear the oolemma Bevel Length: Short bevels (<5 µm) concentrate force, long bevels (>15 µm) risk sliding through the zona


Shallow Angles (25–35°) minimize shear forces on the oolemma and reduce the risk of scraping against the dish. Steeper Angles (>45°) can cause the pipette tip to “dig in,” increasing membrane tears and cytoplasmic leakage. Optimal: Aim for ~30° so the pipette penetrates the zona and oolemma smoothly, preserving spindle integrity.


Optimize Bevel Angle: A 10–15° bevel provides a sharp entry point without weakening the glass wall. Controlled Speed: Advance at a steady, moderate speed—too rapid movement increases shear stress. Pressure Calibration: Set microinjector suction just high enough to hold the oocyte firmly but low enough to prevent sudden pressure spikes. Practice Entry Depth: Aim for penetration just past the zona, avoiding excess travel into the ooplasm.


Zero Reference Point: Park both injection and holding pipettes in designated “home” wells, then set X/Y/Z coordinates to zero. Movement Check: Step through full range of motion (X, Y, Z axes) at low magnification to confirm linear and smooth traverse. Fine-tune under High Magnification: Switch to ICSI settings (400–600×) and make micro-adjustments until pipette tips remain in focus throughout their travel. Record Settings: Log joystick sensitivity and speed parameters for reproducibility across sessions.


Uniform Taper: No kinks or asymmetric walls when back-lit at 200–400× Smooth Bevel: Free of chips, bubbles, or jagged edges at 600× Consistent ID/OD: Measure tip dimensions against a calibrated eyepiece reticle Optical Clarity: Absence of micro-fractures or cloudiness that scatter light


Secure Clamping: Use silicone or soft-grip O-rings on the holder to dampen transmitted vibration. Gentle Insertion: Slide the pipette in until it seats firmly—avoid tightening clamps so much that glass deforms. Anti-Vibration Platform: If available, perform mounting on a specialized table or add small vibration-dampening pads under the scope base.


Pre-polished: Factory-consistent taper and bevel quality Ideal for high-throughput labs needing reproducibility Self-polished (flame-polished): Customizable bevel shape/angle on demand Useful for one-off adjustments or troubleshooting specific oocyte types


Incomplete Priming: Failing to fill tubing and connectors fully with media before use. Leaky Connections: Worn or misaligned O-rings and slip-fit joints allow ambient air ingress. Rapid Pressure Changes: Sudden switching between aspiration and injection can draw bubble-sized air pockets into the line.


Dish Depth & Oil Layer: Steeper angles (35–45°) help avoid scraping the dish bottom. Zona Curvature: A shallow approach (~30°) reduces oocyte rotation on a convex zona. Manipulator Ergonomics: Operator comfort and range of motion often dictate fine adjustments.


90–120 µm taper from the narrowest tip to the thicker shaft Balances rigidity (to prevent flex) with visibility under high magnification Ensures the tip protrudes just past the oolemma without excessive bending


Tight Tolerance (±0.5 µm): Consistent suction force and sperm/embryo handling Reduces batch-to-batch variability in injection pressure Loose Tolerance (±2 µm): May require frequent microinjector recalibration Increases risk of clogging or over-suction


Borosilicate Glass with Filament: Uniform wall thickness, good optical clarity Filament guides even heating and smooth taper formation Quartz Glass (specialty labs): Higher strength, lower autofluorescence (for imaging-intensive work)

FAQ Categories

Click on Your Topic to get answers

Explore More
Intrauterine Insemination
In Vitro Fertilization
Intracytoplasmic Sperm Injection
Injection Micropipettes
Trophectoderm Biopsy (Bevelled) Micropipettes
Trophectoderm Biopsy (Flat) Micropipettes
Zygote Intrafallopian Transfer
History
Gamete Intrafallopian Transfer
Frozen Embryo Transfer
Polar Body Biopsy Micropipettes
Holding Micropipette
Blastomere Biopsy Micropipettes

Got more questions?

Visit our full FAQ Page for in-depth answers or reach out to our Customer Support team.

Monash Biotech Pvt. Ltd.
Change Language
Monash Biotech Pvt. Ltd.

Home

Quality Pledge

About Us

Events Gallery

Blog

News & Updates

Please note that the 3D models displayed on this website are for illustrative purposes only. Actual product dimensions, colors, and finishes may vary.

© 2026 Monash Biotech Pvt. Ltd.. All Rights Reserved.

Designed & Developed by Goafreet Company